With the national response call, my country's new energy cars have been in the forefront of the world. As the technology is getting higher and higher, the requirements for materials and equipment are also increasing. Gas flow mill has been developed and applied. For example, lithium electrical negative graphite, silicon carbon or the like can achieve ultra-narrow particle size distribution and uniform particle shape; lithium battery positive electrode phosphate, high nickel termination material, lithium manganate, etc. Energy Density.
Let's talk about the operating procedures of the airflow crusher and vacuum, the following is the operating procedure of the airflow pulverizer and the vacuum feeder.
Basic knowledge of the airflow crusher, the principle and characteristics of the principle, small The editor has been detailed, let everyone have a general understanding of the airflow crusher, but not a lot, so they will introduce, because its content is not only these, and other aspects, and it is also very important, then below explain in detail.
After the airflow pulverizer compressed air, after filtration, the pulverizing cavity is sprayed through the Raval nozzle, and the material is repeatedly collided, frive, sheared at the intersection of the multi-shaped high-pressure airflow. In the case of pulverizing, the pulverized material is moved with the rising airflow to the grading area under the fan pulleys, and the thick fine product is separated, and the fine particles that meet the granularity requirements of fine particles enter the cyclone by the grading wheel. The separator and the dust collector are collected, and the crude particles drops to the pulverized region to continue to be pulverized.
The airflow pulverizer is low, and all the lifescass are all high-quality wear-resistant materials at home and abroad. The life is long. A small amount of easy wear parts are made of special hard resistance, small size, light weight, easy to replace the accessories. The ultrafine pulverizer is composed of silo, mechanical pulverizer, air blower, cyclone, vibrating screen, liquid nitrogen tank, etc., the deep-cooling pulverizer system is refined by liquid nitrogen as a cold source, and it is crushing at low temperatures by cooling. After the crushing state, enter the mechanical pulverizing cavity through the impeller high speed rotation, the material and the blade, the tooth disc, the material and the material are enrolled under the integrated effect of collision, shear, friction, etc., to achieve a crushing effect.
1. Preparation before starting check host, accompaniment, pipeline, and valve, etc., whether it is intact, whether it works fine.
2. Start
(1) Turn on the compressor power, the dust collector pressure valve, the main air valve, and then turn on the power switch of the airflow pulverizer to turn on the power.
(2) From the zero-start classification wheel, gradually adjust to the specified speed.
(3) Turn on the fan, cyclone separator, drain, and send the motor power supply, then open the total power supply of the feed warehouse, set the frequency of the "frequency", and then start the feed crushing.
(4) The particle size of the finished product can be adjusted by the frequency and feed amount of the grading wheel.
3. Dowsetting sequence: inverter - feeder - Main air valve - Compressor - Section impeller motor - Cyclone dust collector, Dust - Free Amount - Fan - Total Power - Air Compressor.
4. Maintenance
(1) The motor should be lubricated regularly, but the grease should not be too much to prevent the bearing temperature too high.
(2) The wear of the graded impeller, the helical feeder, and the pulverized nozzle should be observed that the tension of the belt should be appropriate.
(3) After pulverizing the material for a period of time, the powder attached to the machine should be cleaned to avoid clogging, thereby affecting the crushing effect.
(4) After the filter bag is used, it must be cleaned or replaced.
5. Precautions
(1) When the unloader is running, the discharge port cannot be extended in hand to avoid accidents.
(2) The speed of the impeller should not exceed the specified value, otherwise the temperature is too high, the impeller and the electric chance are damaged.
(3) Check the safety valve periodically to ensure safety.
Welcome, above the operating procedure for the airflow pulverizer and the vacuum feeder.
At the same time, AlPA loves powder technology with its own excessive quality and good market reputation, and has also gained more and more new customers, Hongrun Petrochemical, three trees coatings. , Ningde Times, BYD Automobile and other enterprises have selected AlPA Love Powder Crusher Products under their own demand.
