Airflow grinding as a new type of high-tech product has achieved significant achievements in the traditional Chinese medicine industry, using gas flow crushing technology in cosmetics industry, enhancing biological utilization, reducing dosage, promoting and expanding absorption, improvement The effect of effect and efficacy. It is mainly used that cell-level fine powder can be absorbed by skin mucosa, and a new way is opened up to further develop traditional Chinese medicine cosmetics.
About Questions on Airflow Crusher, that is, some difficult problems, this is a place where everyone is more confused, and it is also the focus of our study. Because they may encounter in practice. If it does not solve it, then it will affect the use of the airflow crusher. So below, this article will focus on some of the questions in order to answer your questions.
1. Gasflow pulverizer and screen crusher, if compared from the application range, is it wide?
The airflow pulverizer and screen crusher These two are in the field of crusher. However, if you look at the application, then the latter, that is, the application range of the screen crusher is wide. Because the airflow pulverizer is smashing the material within 5 mm, there is a certain limit.
2. The amount of pulverization and treatment of the airflow pulverizer is mainly related to what?
The amount of pulverization and treatment of the airflow pulverizer, which is mainly the specific use of the pulverizer, as well as the specification model, and the like. And by these can determine the size of the airflow pulverizer and the value of the amount of the amount of treatment, so that it is appropriate.
3. If the feed is too small in the airflow mill, then what effect? And what is the collection of finished products in the crusher?
If the feed is too small in the airflow mill, it will affect the pulverizer itself. Attiction will reduce the mass and effect. Because, in the airflow pulverizer, it is high-speed airflow to cause a strong collision to achieve a crushing effect, and the feed is too small to be very good. As for the collection of finished products in the pulverizer, it is achieved by collectors.
4. The particle size of the airflow pulverizer is unstable. What are the specific reasons?
If the airflow pulverizer is unstable, there are two main reasons, one is that the system configuration is unreasonable, or the loss in the system is too large, so that the particle size of the finished product is unstable. Second, there is a change in operation, but it is unqualified or inappropriate to cause the above problems.
5. Can the airflow pulverizer reach 6250?
How much can the static airflow pulverizer particle size? The airflow pulverizer wants to reach 6250 or some difficulties, and for ordinary pulverizer, this requirement is not found. Static airflow pulverizer, its particle size can reach D100.
6. If the air export temperature is high, how can you solve it?
What is the main equipment for the entire airflow crusher system? The airflow puller exit temperature is high, and the fan can be installed at its air outlet to solve the problem. For the entire airflow pulverizer system, it must be included in the air current pulverizer, a grace machine, a fan, and a dust collector.
7. How should the airflow pulverizing machine feed speed and the amount of air?
Want to achieve a good fit between the airflow pulverity feed speed and the amount of air, it can improve the feed speed. And for the fan damper, it should be controlled, it is not too large to avoid the negative pressure inside the pulverizer too much, which affects the crushing effect.
8. What are the specific requirements of the gas flow crusher in the laboratory?
For the basic functions of the pulverizer, it should be carefully and seriously determined, mainly to see if the crusher is pulverized to meet the crushing requirements. And whether it is easy to clean for equipment. Further, in the form, it is also necessary to select the appropriate form according to the actual situation.
9. When the gas flow pulverizer is pulverizing the material, if there is a phenomenon of the outward, is it normal?
If it is blown out when it is smashing the material, then it is definitely a pulverization problem. The reason is that it may be that the branching wheel in the pulverizer is too much. It is also possible that there is a problem for balancing valves, such as the open angle is too large. So to make specific investigations, find out the real reasons to effectively solve it.
10. What should I do correct and reasonable for cyclonic airflow pulverizer?
Airflow pulverizer cyclonic pulverizer, the main requirements in lubrication is to use quality lubricants, and strictly follow the requirements, and use normal operation methods to make their lubrication work . Because this will affect the service life of the device, it is not a horse tiger.
In the context of the era of economic globalization, more and more foreign exchanges have become a inevitable trend in all walks of life, for AlPa powderSay, this communication not only promotes information exchange, but accelerates the pace of ALPA powder to internationalization.
